Support

Support & Installation

We're building something helpful here — installation guides, fit instructions, and answers to common questions for every MATERIUM product.

Can't find your product? Reach us at support@materium.shop and we'll get you sorted.

Find Your Product

Mazda CX-50 Bottle Holder

Compatibility

Fits every CX-50 trim, 2023–2026. The interior layout is shared across the full trim lineup, so this isn't a trim-dependent fit.

This is built specifically for the CX-50's console geometry and is not compatible with the CX-5, CX-30, CX-9, Mazda3, or any other Mazda model. Each of those has a different console shape and mounting area, so a CX-50 holder won't seat correctly in any of them.

How to install

MATERIUM Mazda CX-50 bottle holder install location, showing the ledge next to the factory cupholders where the holder seats, pushed back toward the shifter
  1. Locate the ledge next to your factory cupholders.
  2. Push the holder as far back toward the shifter as it will go.
  3. Press down firmly until it's snug.

No tools, no adhesive. It lifts back out the same way it went in if you ever want to remove it.

Troubleshooting

If it feels loose or won't sit flush, it's almost always because it wasn't pushed all the way back toward the shifter before being pressed down. That's the one step people skip.

Mazda3 Bottle Holder

Compatibility

Fits Mazda3 Gen 4, 2019–2026, both Hatchback and Sedan.

This is built specifically for the Mazda3's console geometry and is not compatible with the CX-50, CX-5, CX-30, CX-9, or any other Mazda model.

How to install

MATERIUM Mazda3 bottle holder installed on the passenger side console ledge near the shifter
  1. Place it on the passenger side console ledge, near the shifter.
  2. Press down until it's snug.

No tools, no adhesive. It lifts back out the same way it went in if you ever want to remove it.

Universal Fit Kit

What's included

  • SLIM bumper ring
  • WIDE bumper ring
  • Solid bottom insert
  • Instruction card
  • Black mesh drawstring storage bag

How it works

The stock opening handles large tumblers as-is, no ring needed. Drop in the WIDE ring for mid-size bottles, or the SLIM ring for anything narrower. The solid bottom insert is for cans and other small containers with no minimum size, since it closes the opening down to hold anything upright rather than fitting to a diameter.

Installing the bumper rings

MATERIUM Universal Fit Kit bumper ring installation, step 1 MATERIUM Universal Fit Kit bumper ring installation, step 2 MATERIUM Universal Fit Kit bumper ring installation, step 3
  1. Choose the ring that best fits your bottle.
  2. Line up the rear tab with the indentation under the rim of the holder to center the ring.
  3. Press down into place.

Both rings are fully removable.

Installing the bottom insert

MATERIUM Universal Fit Kit bottom insert installation, step 1 MATERIUM Universal Fit Kit bottom insert installation, step 2 MATERIUM Universal Fit Kit bottom insert installation, step 3
  1. Drop the insert into the holder from the top, smooth side up.
  2. Press firmly around the edge in a circle until it's fully seated and popped into place.
  3. Bottom of holder and insert will be fully flush when fully installed.

The snug fit is intentional — it prevents rattle and won't shift or fail under a full bottle. To remove, push up from the bottom of the holder to pop it out.

Sizing by ring

Fit option Max diameter Fits (examples)
Stock opening (no ring) 4.0" Stanley Quencher 40oz, YETI 42oz Straw Mug, other large tumblers
WIDE bumper ring 3.55" Owala FreeSip 32oz and similar
SLIM bumper ring 3.12" Owala FreeSip 24oz, Hydro Flask 24oz Wide Mouth, and similar
Solid bottom insert No minimum 12oz cans, energy drinks, other small containers